Toyota Tacoma Access Cab | Sound Solution Install

Designed, engineered and tuned SPECIFICALLY for the Toyota Tacoma Access Cab (3rd Gen ’16-Present)

You vehicle preparation apply parking brake open hood of the vehicle disconnect the negative battery cable prepare a protective surface to place all vehicle components on front door woofer installation remove door panels remove the a pillar by pulling straight and away from the door disengage any clips that remain in the door and return to the a pillar panel disengage

The door locking tab use a panel tool to remove the window door lock control panel it’s a tool between the front edge of the panel of the trim to remove disconnect window door lock control connectors from the panel use of a pick tool or precision screwdriver is needed to release the connector use a pick tool to remove the carpet cover in the grab handle and remove

The number two phillips screw behind the cover use a panel tool to remove the cover behind the interior door latch and remove the number two phillips screw use a panel tool to disengage the clips behind the door panel one at a time start at the bottom then the sides and finish at the top use gentle force to remove the door panel remove door latch assembly from the

Door panel by unsnapping and lifting the latch connectors connectors need to be reassembled in the same orientation white on top green on bottom set door panel aside disconnect the factory six by nine speaker connector remove the four ten millimeter bolts holding the factory six by nine speaker in place and remove the speaker not the oem audio+ six by nine woofer

By using the four ten millimeter bolts and reinstall the six by nine speaker connector resembled or in reverse order taking time to ensure all clips are engaged rear door speaker installation remove door panels disengage door locking tab by pushing the release in and removing use a panel or pick tool to remove the cover behind the interior door latch use a t25 torx

To remove the door latch cover remove the lower seatbelt mounting bolt cover and mounting bolt remove the grab handle use gentle force to remove door panel start at the bottom then the sides we finish at the top you’ll need to pull the seat belt through the seat belt opening to remove the door panel completely disconnect the factory six-and-a-half speaker connector

Remove the three 10 millimeter bolts holding the factory speaker in place and remove speaker not the six-and-a-half om audio+ coaxial speaker by using the three factory ten millimeter bolts and reinstall speaker connector reinstalled or in reverse order taking time to ensure all clips are engaged failure to securely reinstall door panel may results in rattles make

Sure that the seat belt is installed properly ensuring that no binding occurs on the seat belt strap tweeter installation in the – area remove the a-pillar interior trim panel open the plastic cover and remove the 10 millimeter bolt pull panel out of position in a way using a pic or panel tool carefully lift the – speaker grille up and out of position remove the

10 millimeter bolts holding the factory – speaker in place and remove the speaker disconnect the factory – speaker and position that william audio+ one inch soft dome tweeter in position reinstall the – speaker connector and mount using the original ten millimeter bolts reinstall the – bigger grille a pillar interior trim panel and the ten millimeter bolt repeat

Process for the other side of the vehicle amplifier installation loosen the driver seat slide the seat forward and remove the trim panel covering the seat bolts on the rear side of the seat locate the slots in the trim covers and pry them off using the forked end of your trim tool using a fourteen millimeter socket with a six inch extension remove the two rear

Fourteen millimeter seat bolts slide seat to the rear and remove the two front fourteen millimeter seat bolts mount the amplifier tilt the seat towards the rear of the vehicle remove the center cable mounting clip this bundle will be repositioned in house on the oem audio+ amplifier assembly once mounted install and position the two provided speed clips so that

It aligns with the two inner center holes of the under seat frame position the amplifier assembly so that the rear bracket hooks on the rear most spring and the front bracket arm rests on the under seat front frame position om audio plus amplifier bracket support into position and install provided ten millimeter bolts the amplifier connector receptacles will face

The driver side of the vehicle quick sync wiring harness installation remove the driver side front threshold remove the driver side kick panel by unscrewing the black locking tab remove the driver side rear threshold by pulling in an upward motion with the rear seat cushion assembly remove the front and rear center console mats remove the four ten millimeter bolts

Remove the driver side and passenger side rear seat belt assemblies release the lock and fasten the floorboard to the seat bottom disengage the two guides and remove the lower console box remove the console plate by removing the two 12 millimeter bolts and the six number two screws attached to the lower console box using the utility knife cut the carpet along the

Rear under seat storage panel and the seat belt assemblies extend the existing factory slits to your cut completing the right angle this will allow the subwoofer mounting bracket to sit flush underneath the carpet once installed remove under-seat storage panel disengage floorboard using the plastic panel tool remove the 12 push and snaps securing the under seat

Storage panel in place remove the rear seat cushion assemblies by loosening the three 12 millimeter bolts disengage the under-seat storage panel from its rested position by lifting up and removing from vehicle panel modification identify the rear center of the panel this will be the same side of the storage floorboard hinges locate the center of this panel beneath

Where the lower console box rested a one inch hole saw can be used for a large enough opening to allow the subwoofer connectors to pass through without altering the exterior appearance of the panel remove the rear passenger side lower seatbelt mounting bolt fixing wiring harness installation unfasten the white plastic carpet clips along the front driver’s side of

The threshold area lift carpet edge to expose the cable route run the quick sync wiring harness amplifier connectors and ground underneath the carpet opening from the front driver side threshold to the opening used by the factory wiring that connects under the seat leave about six to ten inches of slack for the white and gray connectors from the carpet opening

Locate the factory ground underneath the carpet and remove the 10 millimeter ground bolt install the harness ground together with the factory ground and reinstall the ten millimeter bolt make sure the harness ground rests on top of the factory ground bolt you will be left with the white and gray connectors of the quick sink wiring harness underneath the driver’s

Side seat plug the white and gray 22 pin connectors from the quick sync wiring harness into the designated receptacles of the dsp amplifier white connector inserts into the receptacle towards the rear of the vehicle you want to ensure that the quick sink wiring harness has enough slack so that the cable is an arrested position even when the driver seat is pushed

All the way back route the quick sink wiring harness radio connectors and power wire towards the driver side kick panel area leave the wires in the kick panel floor area for the time being run the length of the subwoofer umbilical cable alongside the driver side threshold towards the rear of the truck disengage and re-engage the plastic white clips along the route

Use cable ties as necessary remove the weather stripping on the rear driver side to access the side rear panel apply pressure to the panel pushing towards the passenger side to disengage the locking tabs only the lower portion this panel needs to be loosened to clear a pathway to run the subwoofer umbilical through to the cavity where the under seat storage panel

Installs run the length of the subwoofer umbilical alongside the driver side threshold and through the available path to this area reinstall the side rear panel weather stripping lower seatbelt mounting bolt rear and front driver side thresholds leave the cable in the center of the rear area for the time being position the under seat storage panel back into the

Vehicle running the sub connector through with six or 12 inches of slack once the panel is in arrested position reinstall rear seat cushion assemblies and all 12 of the under seat storage panel push and snaps apply the provided velcro strip on the under seat panel between the driver and passenger side floorboards subwoofer installation using two ten millimeter

Bolts install the rear storage mounting bracket to the sub one closure install the access cab subwoofer between the driver and passenger side cushion assemblies with the bracket facing the rear of the vehicle lift the modified carpet flap and rest the rear mounting bracket on the bare metal make sure that the enclosure is nestled in place and that the holes of the

Brackets are lined up with the seatbelt bolt holes reinstall the rear seat belt mounting bolts and assemblies seat belt buckles are held in position by the built-in magnets on the oem audio+ access cab enclosure connect subwoofer umbilical cables to the oem audio+ subwoofer these connectors are ambidextrous and can be plugged in any order reinstall floor panels –

Under seat storage panel if remove and reinstall seat cushions – rested positions return driver seat back into place and confirm that the seat bolt poles are lining up tighten the seat bolts by hand at first to ensure proper alignment if there’s too much resistance start over and double check the alignment finish tightening all four seat bolts using your 14 millimeter

Socket and ratchet radio removal remove radio trim by inserting a plastic tool to the bottom edge and carefully pry it away by hand using the socket wrench remove the four 10 millimeter bolts holding the radio in place lay down protective blanket over transmission area disconnect connectors and antenna leads remove radio and store throughout the quicksync wire and

Harness radio connectors and power wire towards the driver side kick panel area use cable ties as necessary run the harness above the accelerator pedal and steering column towards the radio cavity run neatly and out of the way and use cable ties as necessary route the harness towards the radio cavity until the connectors are visible connect the quick sink wiring

Harness into the radio and factory harness using the designated connectors pull power wire through the radio cavity and run towards the passenger side kick panel area fish above the air-conditioning unit into the factory grommet location reinstall all connectors that were originally plugged into the back y do plug in your factory 10 pin and six pin connector into

The quick sink wiring harness and the quick sink wiring harness directly into your radio reinstall radio and trim panel power wire installation under the hood on the passenger side of the vehicle locate the grommet for the main factory wiring harness on the passenger side of the firewall directly below the factory wiring identify the unused nipple and slice the

Tip off to create an opening for the power wire for best results insert a 10-inch wire or cable tie through the grommet from under the hood and attach power wire from the kick panel area run the length of the wire through the grommet you’ll want just enough length to reach your battery cut any additional slack install the supplied high-temperature corrugated

Split loom to cover the power wires and insulate against extreme temperatures under the hood run loomed power wire towards the battery secure using cable ties as necessary use a wire stripper to drip 3/8 of an inch off the end of the power wire connect the power wires to the fuse holder assembly by inserting the 12 gauge stripped power wire into the yellow butt

Connector and crimp apply heat to activate the built-in solder and heat shrink insulator for the best connection possible install the 10 millimeter bolt from the battery positive terminal install the ring terminal of the fuse holder lead reinstall the 10 millimeter bolt of the fuse holder assembly and tighten install the provided fuse reconnect the battery and

Close the hood this concludes the installation of the oem audio+ reference for pdq for the toyota tacoma access cab you

Transcribed from video
Toyota Tacoma Access Cab | Sound Solution Install By OEM Audio +